Robert Evans' Jr Blog

Roofing Valleys Correctly

Posted by Robert Evans on Feb 20, 2019 10:59:42 AM

Welcome to Robert Evans Jr. Contracting

Weaved Valley

Depending on your roof design you may or may not have valleys. A Valley is where 2 roof lines come together. Here is a picture of Robert Evans JR. Contracting Inc. installing a Weaved "Closed valley".  Closed valleys are those where shingles on one or both sides of the roof extend across the valley onto the adjacent roof slope. There is two kinds of closed valleys: cut valleys, which are less expensive to install {due to less waste in material and quicker labor install} and are the most common, and there are woven valleys as you see above in this picture. When Installing the woven method, shingles from both roof slopes run through onto the adjacent slope, alternating with each course. This is done differently with different types of roofing shingles depending on 3-tab, thickness, archtectural type shingles. Woven valleys is not recommended to be installed on a roof pitch less than 4:12. 

Tags: roofing metrowest, Commercial roof, www.certainteed.com, www.gaf.com, roof newton, roofs, CDX plywood, Certainteed Lifetime roof, Architectural shingles, Certainteed Landmark, ice and water barrier, roof Framingham, Gaf, gaf timberline shingles, cobra ridge vent, roof metrowest, roof natick, roof installation, roof leaks, wayland ma., roof leak

Rotted roof boards

Posted by Robert Evans on Sep 9, 2014 1:18:00 PM

Rotted Roof Boards

Welcome to Robert Evans Jr. Contracting

When Homeowners let there roof go without inspection or repair , big problems can arise causing a costly roof replacement become even more costly, sometimes doubling the cost !! If your roof has not been inspected within the last 5 years, please contact us for a free roof evaluation.

Schedule your FREE Roofing Assessment Today!

In alot of cases Rotted roof boards go unseen and not noticed till the roof starts leaking inside the house, causing expensive repairs, structural damage, termites. Making your average roof cost double in cost !!

$300 Roofing Coupon

Tags: www.gaf.com, roof warranty, Rotted roof boards, CDX plywood, carpenter, Architectural shingles, Roof selection, attic ventilation, Rotted roof rafters, roof metrowest, roof natick, roof installation, roof leaks, Four seasons, wayland ma., PVC Composite, roof boards

Flat Rubber roof in Massachusetts

Posted by Robert Evans on Jun 25, 2014 12:10:00 PM

describe the image

This Flat Rubber roof in Massachusetts was completed a few years ago by Robert Evans Jr Contracting Inc.

Flat Rubber roofs can last up to 40 years if well maintained by your roofing contractor. All seams, corners, penetrations in roof, and edge flashing should be inspected annually for wear and tear. Any ponding water on your flat roof should be avoided also to keep your roof at peak performance.

Robert Evans Jr. Contracting can take care of all your roofing needs including Flat roofs, Sloped asphalt shingled roofs, siding, windows, and General Contracting.Click me

Tags: roofing metrowest, www.certainteed.com, roof newton, roofs, clapboard siding, CDX plywood, carpenter, certainteed roof, Certainteed Lifetime roof, Architectural shingles, ice and water barrier, roof Framingham, rubber roof, shed dormer, attic ventilation, Gaf, gaf timberline shingles, cobra ridge vent, siding metrowest, roof metrowest, roof natick, roof installation, roof leaks, Milford roof, solar metrowest, Four seasons, harvey replacement windows, Floor guys, Firestone roofing, firestone contractor

Vinyl siding

Posted by Robert Evans on Feb 3, 2014 1:17:00 PM

-Request a Qoute!

Vinyl siding is plastic exterior siding for a house, used for decoration and weatherproofing, imitating wood clapboard, and used instead of other materials such as aluminum or fiber cement siding. It is an engineered product, manufactured primarily from polyvinyl chloride (PVC) resin.

Approximately 80 percent of its weight is PVC resin, with the remaining 20 percent being ingredients that impart color, opacity, gloss, impact resistance, flexibility, and durability. It is the most commonly installed exterior cladding for residential construction in the United States and Canada.

 

 

History

Vinyl siding was introduced to the exterior market in the late 1950s as a replacement for aluminum siding. It was first produced by an independently-owned manufacturing plant called Crane Plastics in Columbus, Ohio. The process was originally done through mono-extrusion. At that time, blending of colors was done manually.

This original process made it difficult to produce and install a consistent, quality product. Beginning in the 1970s, the industry changed its formulation changes to improve the product's production speed, impact resistance, and range of colors.

In the following decade, vinyl siding grew steadily in popularity in large part due to its durability, versatility, and ease of maintenance. However, in many European countries, for instance Germany, vinyl (PVC) is rarely used or phased out because of its negative environmental profile.

Modern manufacture

Today, vinyl siding is manufactured by coextrusion. Two layers of PVC are laid down in a continuous extrusion process; the top layer is weatherable capstock, which comprises about a third of the siding thickness. This capstock includes about 10% titanium dioxide, which is a pigment and provides resistance to breakdown from UV light. Vinyl siding, like paint, will inevitably fade over time, but the fade rate is somewhat slower with vinyl, and in any house cladding (vinyl, paint or others) the intensity of the color is in direct correlation to the rate of fade. For example, two currently popular colors are "barn red" and "clay". In reaction to sunlight, the barn red will fade faster than the very neutral clay color whether paint, vinyl siding or other composition. The lower layer, known as substrate, is typically about 15% ground limestone (which is largely calcium carbonate). The limestone reduces cost, and also balances the titanium dioxide, keeping both extrusion streams equally fluid during manufacturing. A small quantity of tin mercaptan or butadiene is added as a stabilizer to chemically tie up any hydrochloric acid that is released into the PVC material as the siding ages. Lubricants are also added to aid in the manufacturing process.

Specs and product variables

Vinyl siding can be observed in a wide range of product quality realized in a substantial difference in thickness and lasting durability. Thickness can vary from .035" in cheaper grade siding products up to .052" in the highest grade products which vary from manufacturer to manufacturer. Today, the thinnest vinyl siding commonly used is .040", and is known as "builder's grade". Vinyl product can vary in thickness even within one manufacturer up to .010" of thickness through varying product lines offered that range from basic to premium-grade products. Thicker vinyl products, usually realized in higher cost, are more rigid which can add to the aesthetic appeal and look of the installed, inherently flexible product and also add to durability and life expectancy. Thicker grades of vinyl siding may, according to some, exhibit more resistance to the most common complaint about vinyl siding – its tendency to crack in very cold weather when it is struck or bumped by a hard object while others feel that a thinner product may allow more 'flex before cracking' and is a subject of debate. However, at "This Old House" website, this assertion about thickness and crack resistance is disputed. They claim to know of test results that indicate chemical makeup has a greater influence on impact resistance than does thickness.

Chemical formulas can also vary somewhat from manufacturer to manufacturer which can impact life expectancy as formulas and possibly manufacture process can be one of the most important in terms of product quality and durability. One important advent was a UV coating,  utilized by some manufacturers that was applied to the surface of the product that filters out UV spectral light from the sun which would otherwise degrade the PVC more quickly. As a rough general rule, the higher the grade (and price) of the siding, the more resistant it is to fading (intensity of the color being taken into consideration, as mentioned above).

Vinyl siding is manufactured with its own partial fastening or locking system that is coupled with nails that 'loose' fasten the product to the exterior wall. This locking system can be either a rolled or an extruded lock depending on the manufacturing process, either of which has its own design considerations. This locking system, either extruded or rolled has a bottom lock which locks into either a start piece or onto the top lock of the panel below. The top lock is then 'loose' nailed to hold the panel to the wall. This 'loose' nailing allows for float which is created by expansion and contraction from varying temperature and weather conditions. With well designed siding, and proper 'loose nailing' installation, the siding can easily expand up, down, in and out, and left and right without restriction. Vinyl siding, by its nature, will tend to expand and contract more with temperature extremes than any other common type of cladding.

Environmental aspects

From an environmental standpoint, vinyl (PVC) siding has been called a "disaster". The production of PVC and its feedstocks, vinyl chloride monomer and ethylene dichloride results in the release of hundreds of thousands of pounds of toxic chemicals into the environment each year, mainly in poor, communities of color in Louisiana and Texas. PVC production is also a large source of dioxin into the environment.

Vinyl siding, like natural wood siding, is flammable. The natural fire retardancy of PVC is a double-edged sword in that building materials may smolder for long periods of time giving off hydrogen chloride gas long before visible signs of fire appear. Because of its majority chlorine content, when PVC burns in fires two extremely hazardous substances, hydrogen chloride gas and dioxin are formed which present both acute and chronic health hazards to building occupants, fire fighters and surrounding communities. In addition, when PVC burns, some 100 different toxic compounds are produced. Because of its thin profile, vinyl siding may be more likely to ignite due to exterior fire; for example, the National Institute of Standards and Technology found that, in tests involving vinyl-clad structures in close proximity, fire was observed to spread between two vinyl-clad test structures located six feet apart in fewer than five minutes.Additionally, vinyl siding can release toxic fumes when burning, particularly dioxins. This is not only an environmental concern, but the fumes can be dangerous to firefighters and bystanders, and the toxic fumes released may increase the likelihood of fatality from smoke inhalation for anyone trapped in the burning structure.

The National Association of Home Builders (NAHB) recommends using building materials that require "no additional finish resources to complete application on site" for green home builders as they reduce waste and materials used. Installing vinyl siding involves neither paint, stain, nor caulk and thus meets this NAHB requirement.

Environmental Building News wrote in its January, 1998 issue that "while Greenpeace has been most vocal regarding environmental and health concerns with PVC (vinyl), they are by no means the only voice out there expressing such concerns. There is widespread concern within the environmental and toxicology communities, not only about PVC and the products associated with its manufacture and disposal, but also about chemicals that are added to PVC to give it specific properties for building product applications. The plasticizer DEHP, for example, has been the focus of recent concern. "we stand by our concerns about PVC-based building products for both environmental and health reasons."—ebn, January 1998, page 3.] The position of the International Association of Firefighters, which represents fire fighters in the U.S. and Canada is: "Due to its intrinsic hazards, we support efforts to identify and use alternative building materials that do not pose as much risk as PVC to fire fighters, building occupants or communities."

The PVC used in vinyl siding used to be produced in open vats until 1971, when angiosarcoma, a rare cancer of the liver, was traced to vinyl chloride exposure among PVC workers, and strict workplace exposure limits were established by the Occupational Safety and Health Administration. These changes required all vats to be tightly sealed, which led to greater capital costs and a concentration in the number of producers.

 

Tags: roofs, replacement windows, vinyl siding, clapboard siding, CDX plywood, Gutter Guards, carpenter, siding metrowest

Certainteed Framingham Roof

Posted by Robert Evans on Sep 4, 2013 2:58:00 PM

This large ranch in Framingham Ma. called on Robert Evans Jr. Contracting to install a Lifetime Certainteed Landmark Architectural shingles with a Granite Gray color. WWW.Certainteed.com.

 

describe the imagedescribe the imagedescribe the imagedescribe the imageSchedule your FREE Roofing Assessment Today!

Tags: www.certainteed.com, CDX plywood, certainteed roof, Certainteed Lifetime roof, Architectural shingles, Certainteed Landmark, ice dams, ice and water barrier, roof Framingham, cobra ridge vent, ice dam framingham, roof installation, roof leaks

Natick roof

Posted by Robert Evans on Aug 27, 2013 11:23:00 AM

A mu

much needed roof in Natick. New Gaf shingles and a whole lot of wood replacementIMG 2183MA30907948 0001 resized 600IMG 9291MA30907950 0002 resized 600IMG 7364MA30907951 0003 resized 600

Tags: CDX plywood, Architectural shingles, ice and water barrier, Gaf, roof metrowest

Copper Roof

Posted by Robert Evans on Apr 5, 2013 12:20:00 PM

photoMA30890658 0002 resized 600photoMA30890660 0001 resized 600Example of a poorly installed flat seam copper roof. The roof was installed only a year ago on a newly constructed house, the roof had no pitch, but if properly install the copper still should not have leaked. The joints on the flat seam copper were not sweat properly, which allowed standing water to penetrate. We came in and removed the copper and installed a pitch with tapered ISO and fastened ½ inch plywood over. High temp ice and water is than placed on plywood. New 16 oz flat seam copper roof is than reinstalled.


Tags: CDX plywood, ice and water barrier, copper roof, standing water, metal roofing

Attic Exhaust Ventilation

Posted by Robert Evans on Dec 5, 2012 1:37:00 PM

Schedule your FREE Roofing Assessment Today! 

Effective attic ventilation is critical for a long-lasting roof ! A properly balanced attic ventilation system will help to:

  • Remove excess heat and moisture to protect your roof from premature deterioration
  • Prevent roof rot in your attic or roof deck
  • Minimize peeling and extend the life of exterior and interior paint
  • Limit the growth of harmful mold
  • Safeguard your attic possessions against mildew damage
  • Guard against ice damming in harsh winter climates
  • Possibly reduce excessive heating and air conditioning costs

Stale Air Escapes Through Cobra Exhaust Vent { Installed under ridge cap shingles }Fresh air enters attic through intake vent at soffit or eave

www.gaf.com

-Speak to a Roofing Professional!-Having Roof Issues? Schedule Your FREE Roofing As

 

Tags: CDX plywood, ice dams, attic ventilation, cobra ridge vent, Re-sheathed

Robert Evans Jr. Roofing In Hollistion Ma.

Posted by Robert Evans on Jun 18, 2012 8:48:00 AM

BeforeHollistonAfter 

Robert Evans Jr Contracting was hired to reroof this split level home in Holliston Ma. It needed to be Re-sheathed with 1/2 CDX plywood before installing a Certainteed Lifetime Architectural shingle. When Stripping the old roof off we discovered the plywood to be de-laminated and having dry rot, causing the wood not safe and not strong enough for bearing any weight. All work and workers are fully insured on evey job completed by Robert Evans Jr Contracting.

Tags: CDX plywood, Certainteed Lifetime roof, roof installation, Re-sheathed